黄色无码在线观看免费,亚州a√无码国产一二区,亚洲日韩精品秘 在线观看,亚洲精品一区二区三区BBB,99精品无人区乱码1区2区3区
Hotline:13924627849

Lasted News:

更多

Contact Us

Shenzhen Haolin Pml Precision Mechanism Ltd
Hotline:400-6846-806
Fax:0755-84196969
Tel:13924627849 (Mr.Hou)
Tel:18922863481 (Ms.Lai)
-mail:houlz@szhaolin.com.cn
Add:building 2, Huaguan Industrial Park, No. 63, Zhangqi Road, Guixiang community, Guanlan street, Longhua District, Shenzhen,china

Industry News

You are here:Home >> News >> Industry News
Dispenser operating procedure FAQ
Publish:電子產(chǎn)品全自動(dòng)柔性組裝線,深圳市豪林精密機(jī)械有限公司  Time:2013-12-25
The most common problem encountered is the dispenser valve problems , to solve the following problem occurs when using plastic valves often an effective way .

One of the common problems process dispenser drip dispensing valve operation
1 After this happens often related to the completion of the dispensing valve .

2.95% of such cases are caused because the caliber of the needle used is too small.

3 small needles will affect the flow of the liquid causes back pressure , resulting in the formation of the phenomenon shortly after the completion of drip dispensing valve closed . The needle is too small will affect exhaust valve begins to bubble gum action when used as long as the replacement of a large needle to solve this problem.

4 backpressure tapered helical needle produces the least liquid flow most smoothly.

5 after the air within the liquid dispensing valve produces complete drip off phenomenon , it is best to preclude liquid air , or use of a bubble-containing gel is not easy . Centrifugation or gel first using the deaeration .

Two sizes of glue dispensing operation process inconsistencies FAQ
1 When the glue is inconsistent mainly for storage of fluid pressure cylinder or air pressure generated by instability .

2 meter inlet pressure regulator should be set at the lowest of low pressure over the factory 10 to 15psi., The pressure should be between the pressure tube using a pressure regulator above the middle of the table , you should avoid using a pressure gauge between being low pressure parts.

3 dispensing valve control pressure should be at least 60psi or more in order to ensure the stability of the plastic .

4 Finally, you should check out the glue time if less than 15 / 1000 seconds will cause the plastic instability . , Glue glue more time to grow more stable .

Three of the flow rate is too slow process of dispensing operations FAQs
1 If the flow rate is too slow pipeline should be from 1/ 4 "to 3/8 ."

2 If there is no need for the pipeline should be as short as possible .
3 In addition to change the tube , but also change the plastic mouth and pressure , so full speed up the flow rate.

Four bubbles within the fluid dispensing process operating FAQ
1 . Excessive fluid pressure if coupled with the valve open time is too short compared with the liquid may penetrate the air . Solutions to reduce the fluid pressure and the use of conical oblique needle .

       
2 V. glue dispensing operation of the process FAQ blocked.

3 such cases is mainly due to excessive moisture or repeated used instant glue . Be sure to use fresh, instant glue . The pipeline does not contain moisture Aceton with acetone thoroughly cleaned . After air drying for use should be determined between the plant and the installation of pneumatic valve system with plastic filter . ( If the above method does not work, you should use nitrogen ) .

Dispensing needle selection method :

1 . Four criteria : a small point - small needles, low- pressure , short-term high point - a large needle , greater pressure , longer concentrated glue - inclined needles, greater pressure , the time needed to set an aqueous liquid - small needles, small pressure needed to set the time .

2 . Fluids require special settings :

( 1 ) instant glue : water-based instant glue safe piston and Teflon -lined metal needles, for the thick of instant glue , use a tapered helical needle , For flexible use PP needle.

(2) UV glue : Use amber syringes, needles white piston and inclined (which can block ultraviolet ) .

( 3 ) light-curing adhesive: use black opaque syringes, white piston , the needle can block ultraviolet .

( 4 ) Anaerobic : Use 10CC syringes and white PE common piston .

( 5 ) and paste sealant fluid : If using white piston rebound serious , please use the security style living style , using oblique needle .
Previous:  2019/10/26
Next:Automatic Screw Machine FAQ  2013/12/25
最猛黑人熟妇性HDXXX | 特大巨人黑人AAA片BBC | 精品久久久久久无码人妻蜜桃免费 | 色噜噜亚洲丰满熟妇AV片 | 黄色视频久久人妻91 | 国产高清在线多人视频 | 大乳爆乳午夜A∨片91 | 大地资源国产精品系列 | 久久av高潮av无码av喷吹 | 亚洲第一精品人人澡人人爽 | 国产乱人妻精品 9 2 1 5入口免费 | 一道本久在线中文字幕 | 丰满人妻日本久久久久 | 91久久无码一区人妻A片蜜桃 | 午夜福利一区二区三区 | 中文字幕无码人妻av | 亚洲AV无码秘 桃乃木中文 | 人人妻人人澡人人爽DVD | 99精品无人区乱码1区2区3区 | 10000部拍拍拍18勿入中国 | 久久精品亚洲精品国产欧美 | 亚洲色成人www永久网站 | 国产欧美又粗又猛又爽欧美老人做爱 | 亚洲中文字幕在线播放 | 久久综合精品成人电影 | 成人A片网站发布地址 | 天堂AV免费在线观看 | 中国一级黄色电影 | 无码人妻精品一区二区三区老鸭窝 | 中文字幕丰满子伦无码专区 | 91精品国偷拍自产在线观看 | 四州少妇BBw搡BBBB小说 | 亚洲精品国产成人综合久久久久久久久 | 女教师国产又大又粗免费看A片 | 人妻出轨中出欲求无码视频 | 在线观看免费黄色小视频 | 国产精品久久久久久久久久影院 | 国产群交内射一区二区三区四区 | 波多野结衣毛片在线观看 | 色欲午夜aa成人影院在线观看 | 国产91 丝袜在线播放 |